|
|
|
Who's Online
There currently are 5873 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I was impressed with the quality of service (frequent e-mails to let you know the status of your order), and the speed at which the download became available. The manual was a life saver and was not easy to track down. Thank you for such an excellent service.
;
the manual was just what i wanted it had all the revelent information required to operate the hifi .Iwould use any manual i downloaded for any item which needs a manual
;
Die gewünschte Bedienungsanleitung wurde vereinbarungsgemäß in deutsch bereitgestellt. Sie ist gut lesbar. Kein Kauderwelsch.
Danke für den Service.
;
GOOD SERVICE MANUAL GOT ALL THE INFO. THAT I NEEDED..
;
Excellent product and service. I bought a second-hand Casio CPS-60 keyboard which had no manual. Packed full of features which I had no idea how to operate . . .
Google search found this site (and others with the same manual for sale for $8.99!)
I bought the manual and within an hour the download was available. Quality of the scanned images is good - very clear - and the PDF has been created with the pages in the correct order.
I would definitely use this site again.
The S1500 / S2000 Protection Circuitry
As noted in the �Guided Tour� section of this manual, the S1500 / S2000 frontpanel Protection LED indicates the activity of the relay speaker connection circuitry. When the Protection LED is lit, this circuitry is active, and all connected speakers are muted (provided with 0 volts DC), thus protecting them and preventing any audible �thump� from occurring. The following conditions will cause the Protection LED to go on: � Initial power-up: For approximately five seconds after initial power-up, the protection circuitry is activated and the speaker output is muted. If everything is operating normally, you will hear an audible click at the conclusion of this brief period, as the protection circuitry is deactivated and the S1500 / S2000 begins delivering signal to connected speakers (at which point you�ll hear a click). It is normal for the Protection LED to fade gradually after the amplifier is powered off. WARNING: If the Protection LED fails to go out (and you fail to hear the accompanying audible click) approximately five seconds after power-up, turn the S1500 / S2000 off immediately and check all external devices and wiring for possible shorts or other defects. � Overheating: A temperature sensing device in the S1500 / S2000 will cause the protection circuitry to be activated (and the Protection LED to go on) whenever the operating temperature of the unit rises above a safe level. To guard against this problem, make sure the S1500 / S2000 receives adequate ventilation on all sides and that both the front and rear panels are unobstructed. � Severe overcurrent conditions: This occurs whenever the signal being input to the S1500 / S2000 rises to a level above 20% THD (Total Harmonic Distortion). � Shorted speaker cables: This will occur if, due to faulty wiring, the hot and ground signals being output by the S1500 / S2000 short one another. � Output impedance drops below 2 ohms: This can occur if the S1500 / S2000 is connected to inappropriate speaker systems (see the �Setting Up and Using Your S1500 / S2000� section on page 5 in this manual for more information). � DC voltage detected at speaker output: The most likely cause of this is an internal failure.
PROTECTION
In general, any time the Protection LED lights up (other than during the approximately five seconds following initial power-up), there is reason to be concerned. If this occurs, turn the S1500 / S2000 off immediately and carefully check all wiring and external devices in order to locate and correct the condition that caused the LED to light up in the first place. For further assistance, contact your local Samson dealer. If purchased in the United States, you can call Samson Technical Support (1-800-372-6766) between 9 AM and 5 PM EST.
6
|
|
|
> |
|
